Are you looking for a guide on removing glued motorcycle grips?
The good news is that there are many ways to get rid of them, and we have a step-by-step guide that will help you remove those pesky grips without any trouble.
You’ll be able to save yourself some time and money by following our guide. Not to mention, it’s a whole lot less messy.
Read more about how to remove glued on motorcycle grips below.
Why Does The Motorcycle Grip Need to Be Removed?
The main reason why the motorcycle grip needs to be removed is that it is worn out. Over time, the motorcycle grip will become loose and will no longer provide the same level of comfort and grip.
Another reason why you may need to replace your grips is if you are changing the handlebars on your motorcycle. In this case, you will need to remove the old grips before you can install the new ones.
Also, if you are simply looking to change the look of your motorcycle, then you may want to consider replacing the grips.
Method of How to Remove Glued On Motorcycle Grips
There are a few different methods that you can use to remove glued motorcycle grips.
The first method is to use a grip adhesive remover. This is a chemical solvent that will dissolve the adhesive that is holding the grip in place. You can find this type of product at most hardware stores or online.
Use a Grip Adhesive Remover
1. To use a grip adhesive remover, you will need to apply it to a clean cloth and then rub it onto the grip.
2. Be sure to follow the instructions on the label of the grip adhesive remover.
3. Once the grip adhesive remover has had a chance to work, you should be able to peel the grip off of the handlebar.
4. If the grip is still stubborn, you can use a putty knife or a similar tool to help pry it off.
The second method is to use a heat gun. This will soften the adhesive and make it easier to remove the grip.
Use a Heat Gun
1. To use a heat gun, you will need to hold it about 6 inches away from the grip.
2. Move the heat gun around so that the entire grip is heated evenly.
3. Once the grip is heated, you should be able to peel it off of the handlebar.
4. If the grip is still stubborn, you can use a putty knife or a similar tool to help pry it off.
You can also use a hairdryer for this method, but be careful not to overheat the grip as this can damage it.
Use a Hairdryer
1. Set the hairdryer to its hottest setting and hold it close to the grip, moving it back and forth until the grip is heated through.
2. Once the grip is hot, use a blunt object to begin prying it off. Start at one end and work your way around until the grip pops off.
3. If the grip is still proving difficult to remove, heat it up again and try prying it off once more.
The third method is to use a razor blade. This is the most dangerous method, but it is also the most effective.
Use a Razor Blade
1. Carefully slide the razor blade under the grip, being careful not to cut yourself.
2. Apply pressure to the razor blade and carefully slice through the glue.
3. Slowly peel back the grip, using the razor blade to help if necessary.
4. Repeat steps 1-3 until all of the glue has been removed.
5. Clean up any residual glue with a rag and some acetone.
Once you have the grip removed, you can then proceed to install the new one.
Now that you know how to remove glued motorcycle grips, you can easily change them out when necessary. Be sure to be careful when using a razor blade, and always clean up any residual glue afterward.
Additional Information
If you are having difficulty removing the grips, you can also try soaking them in warm soapy water for a few minutes. This will help to loosen the adhesive and make them easier to remove.
You can also use a product called Goof Off to help dissolve the adhesive. This is available at most hardware stores.
If you are changing the handlebars on your motorcycle, you will also need to replace the bar end weights. These are located at the end of the handlebars and help to balance them.
Be sure to check your owner’s manual for specific instructions on how to change the grips on your motorcycle.
Tip for A Better Motorcycle Grip
Here is a tip on how to get a better motorcycle grip. When you are removing the old grip, be sure to clean the surface of the handlebar thoroughly. Any dirt or grime that is left behind will make it more difficult for the new grip to adhere properly.
It is also good to apply a thin layer of grip adhesive to the handlebar before installing the new grip. This will help to ensure that the grip stays in place and does not slip.
If you are looking for a better motorcycle grip, consider using handlebar tape. This fabric is wrapped around the handlebars and provides added comfort and grip.
It is also relatively easy to install and remove, so it is a good option if you frequently change your grips.
Be sure to clean your handlebars before installing new grips. This will help to ensure that the grips adhere properly and do not come off easily.
You can also use a product like “Grip-On, ” a rubber-based spray adhesive. It’s easy to apply and remove, and it won’t damage your bike.
Final Thoughts
Changing out your motorcycle grips is a relatively easy process that can be done at home. Be sure to take your time and follow the instructions carefully to avoid damaging your bike. Most importantly, be sure to clean the surface of the handlebar before installing new grips. This will help to ensure that they adhere properly and do not come off easily. Thanks for reading!